MAX15096GWE+T by Analog Devices

2.7V to 18V, 6A Integrated Hot-Swap/Electronic Circuit Breaker

Status: Active
Series: MAX15096, MAX15096A
RoHS: Unknown
View Datasheet Manufacturer Site View Pricing & Stock

The MAX15096 family of devices are integrated solutions for hot-swap applications requiring the safe insertion and removal of circuit line cards from a live backplane.They can also be used as electronics circuit breaker for hard drive and solid-state drive and fans. The devices integrate a hot-swap controller, 12mΩ (typ) power MOSFET, and an electronic circuit-breaker protection in a single package. The devices are designed for protection of 2.7V to 18V supply voltages. These devices implement a foldback current limit during startup to control inrush current, lowering di/dt and keeping the MOSFET operating under safe operating area (SOA) conditions. After the startup cycle is complete, on-chip comparators provide VariableSpeed/BiLevel™ protection against short-circuit and overcurrent faults, and immunity against system noise and load transients. The load is disconnected in the event of a fault condition. The devices are factory calibrated to deliver accurate overcurrent protection with ±10% accuracy. During a fault condition, PG goes low and the devices latch off (MAX15096) or automatic retry (MAX15096A); the output could also be discharged after a fault event (MAX15096D). The devices feature an IN-to-OUT short-circuit detection before startup. The devices provide a power-MOSFET GATE pin to program the slew rate during startup by adding an external capacitor. The devices have an undervoltage/overvoltage input pin (UVOV) that can detect an undervoltage/overvoltage fault and disconnect the IN from the OUT. Additional features include internal overtemperature protection and a power-good output (PG). The devices are available in a 16-bump, 2mm x 2mm wafer-level package (WLP) and are rated over the -40°C to +105°C extended temperature range.

Prices starting from US$1.70


Distributor Starting From Stock
Logo for Newark Electronics Newark Electronics US$1.87
-
Buy Now
Logo for element14 element14 US$1.74
-
Buy Now
View Full Pricing & Stock Comparison

Features

Integration Reduces Solution Size for Blade Servers and Other Space-Constrained Designs Integrated 12mΩ (typ) Internal Power MOSFET Programmable Overvoltage Protection and Undervoltage-Lockout Threshold Drive-Present Signal Input (Active-Low PRSNT pin) Thermal Protection
Integrated 12mΩ (typ) Internal Power MOSFET
Programmable Overvoltage Protection and Undervoltage-Lockout Threshold
Drive-Present Signal Input (Active-Low PRSNT pin)
Thermal Protection
Flexibility Enables Use in Many Unique Designs 2.7V to 18V Operating Voltage Range Programmable Inrush Current Control Under SOA Operation Adjustable Circuit-Breaker Current/Current-Limit Threshold Programmable Slew-Rate Control Variable-Speed Circuit-Breaker Response Latchoff (MAX15096) or Automatic Retry (MAX15096A) Options
2.7V to 18V Operating Voltage Range
Programmable Inrush Current Control Under SOA Operation
Adjustable Circuit-Breaker Current/Current-Limit Threshold
Programmable Slew-Rate Control
Variable-Speed Circuit-Breaker Response
Latchoff (MAX15096) or Automatic Retry (MAX15096A) Options
Safety Features Ensure Accurate, Robust Protection 6A (max) Load Current Capability ±10% Circuit-Breaker Threshold Accuracy IN-to-OUT Short-Circuit Detection Open-Drain PG Output Output Discharge After a Fault Event (MAX15096D Only) Programmable Additional Delay (2µs max) to Fast-Comparator Response Time Enable Input (EN)
6A (max) Load Current Capability
±10% Circuit-Breaker Threshold Accuracy
IN-to-OUT Short-Circuit Detection
Open-Drain PG Output
Output Discharge After a Fault Event (MAX15096D Only)
Programmable Additional Delay (2µs max) to Fast-Comparator Response Time
Enable Input (EN)

Specifications

VIN (V) (min) 2.7
VIN (V) (max) 18
Current Limit (A) (min) 1.3
Current Limit (A) (max) 6
# Channels 1
Internal Pwr. MOSFETs NMOS
RON (mΩ) (typ) 12
Current Limit Accuracy (%) 10
Fault Response Latchoff
Oper. Temp. (°C) -40 to +105
Package/Pins WLP HC/16
BudgetaryPrice (See Notes) 1.29


MAX15096GWE+T Power Management ICs - PMIC by Analog Devices

HOT-SWAP CONTROLLER, -40 TO 105DEG C

Status: Unknown
Series: -
RoHS: Compliant
View Datasheet Manufacturer Site View Pricing & Stock

Specifications

RoHS Compliant YES

Alternative Descriptions

Hot-Swap Controller, -40 To 105Deg C Rohs Compliant: Yes |Maxim Integrated/analog Devices MAX15096GWE+T | Newark Electronics

Frequently Asked Questions

Where can I find additional details, specifications and documents for a MAX15096GWE+T ?

Additional datasheets, footprints and schematics for MAX15096GWE+T are listed on our Part Details page. You can also find images and similar parts to MAX15096GWE+T on this page.

What pricing and inventory information can I view?

Distributor pricing and stock information is available for MAX15096GWE+T on our Product Comparison page. Access via the 'View Pricing & Stock' button to view MAX15096GWE+T price breaks, MOQs, lead times, inventory and SKUs from distributors.

Who can I contact for technical support of the product?

Submit any questions directly to the customer support team of the distributor listing the product. For the MAX15096GWE+T you can contact the distributor directly for product support, shipping queries etc.

Is the MAX15096GWE+T RoHS compliant?

This part has not been flagged as RoHS Compliant.

Which authorised distributors for MAX15096GWE+T have stock available?

Authorised distributors including Newark Electronics, element14 and Farnell have stock available or on a lead time for MAX15096GWE+T .

How do I check stock and lead times for all distributors?

Stock availability and lead times will be displayed for MAX15096GWE+T often in real-time on the comparison pages.

What if I can't find stock of MAX15096GWE+T ?

You can fill out our help required form which you can use to request a quote for MAX15096GWE+T from some of our verified obsolescence suppliers. Alternatively, contact us via our web chat in the bottom left of your screen and one of our team will try to help.

We use cookies to improve your experience. See our privacy policy.
Okay